9W2339 Motor Grader Curved Blade 6 Holes 3/4″ Bolt, Motorgrader Bolt On Blade, Low Price Dbc Grader Blades, CATERPILLAR Curved Grader Blade, CAT Genuine Parts Motorgrader Curved Double Bevel Blade, G.E.T Parts Boron Steel Center Blades with 6 holes, Through Hardened Heat Treated Cutting Edges for Motor Grader China Supplier
9W2339 Motor Grader Curved Blade 6 Holes 3/4″ Bolt Specifications:
Part No. 9W2339, 9W-2339
OEM
9W2339
Manufacturer
Caterpillar
Machine
Grader
A 203mm Material HIGH CARBON
B 19mm Diameter 3/4″
C 1219mm Tooth
D Holes 6
E Class
F
G
R
Weight 34Kg
Cutting Edges
• Complete line of curved double bevel (CDB) cutting edges for every make and model
• CDB sizes range from 1/2″ x 6″ for light grading up to heavy-duty 1″ x 8″ CDB section for greater wear life
• Flame-hardened grader cutting edges with surface hardness up to 62 RC, provides max mum wear resistance
• XHD flat grader blades are available in sizes 3/4″ x 8″ through 3″ x 16″ FDB
• Select serrated grader blades are available for frozen or hard packed ground conditions
1. Use tool (A) as shown to make sure the fuel injection rack will move freely by its own weight when injector (1) is turned a total of 180° in both directions. Check the rack movement with the injector spring under compression in several positions. CAT Motor Tractor Blade 9W2329, 9W-2329 6 Holes 3/4″ Bolt
To prevent a carbon deposit between the injector and the injector bore, make sure the injector body (especially the tapered area) and the injector bore are clean and free of foreign material. 9W2323, 9W-2323 Caterpillar Motor Grader Blade 16 Holes 5/8″ Bolts Motor Tractor Blade
2. Make sure the three O-ring seals (2) are installed in injector (1), and put 5P960 Multipurpose Grease on the seals and in the bore in the injector.3. Make sure the plug that the anvil of clamp (3) sets on is installed in the top of the cylinder head assembly. Put clean engine oil on the plug and the anvil of clamp (3).
Do not tap or hit on the injector follower to install the injector. Damage and failure of the injector can be the result. 5D9731, 5D-9731 Ground Engaging Tools Motor Grader 16 Blades Motor Tractor Blade Tractor Central Blade
4. Put injector (1) in position in the cylinder head assembly. Install clamp (3), and tighten the bolt and washer to push injector (1) all the way into its bore. Tighten the bolt to a torque of 65 7 N m (48 5 lb.ft.). CAT Tractor Blade 9W2328, 9W-2328 6 Holes 5/8″ Bolts 5. Check to make sure the fuel injection rack moves freely by hand in the injector after the injector is installed.6. Put lever assembly (4) in position. Connect the lever assembly to control rod (5), and make sure lever assembly (4) is engaged correctly with the fuel injection rack. Install the two bolts to hold the lever assembly in place.7. See Testing And Adjusting module for the correct adjustment of the fuel injection control group. Make sure the control group can move to the fuel 5D9732, 5D-9732 HB500 Through Hardened Curved Grader Blade Tractor Central Blade
Start By:a. remove exhaust manifold The exhaust manifolds do not have to be removed unless all the cylinder head assemblies are to be removed.1. Drain the coolant from the cooling system.2. Shut off the fuel supply on the engine. 3. Remove fuel lines (2), thermocouple (1) and the fuel line manifold from the cylinder head assembly. 4. If equipped, disconnect hose assembly (4) from water manifold (3) 7T1641, 7T-1641 Caterpillar Machine Grader Curved Edges. Remove the bolts to remove a section of water manifold (3) and elbow (6) from the cylinder head assembly.5. Remove bracket (5) from the cylinder head assembly. Air inlet elbow (7) does not have to be removed from the cylinder head assembly, only the bolts that hold the elbow to the cylinder head assembly.6. Remove the bolts, and remove air inlet elbow (7) from the cylinder head assembly. 7. Remove the access cover from under the cylinder head assembly. Remove the bolt and cap (9) to disconnect rod assembly (8) from fuel control shaft (10).8. Remove the rocker shaft assemblies and push rods. See Remove Rocker Shaft Assemblies And Push Rods for this procedure. 9. Remove bolts (14) to remove lever assembly (13) and rod assembly (8) as a unit from the cylinder head assembly. If the lower end of rod assembly (8) does not have enough clearance to be removed, use tool (A) to turn the flywheel until the lower end of rod assembly (8) can be removed between the camshaft and engine block.10. Remove the bolt and clamp (12) from the fuel injector. 7T1639, 7T-1639 High Carbon Curved Cutting Edge for Motorgrader