9W2317, 9W-2317 CAT Grader Edge 10 Holes 5/8″ Bolts, Motorgrader Bolt On Blade, Low Price Dbc Grader Blades, CATERPILLAR Curved Grader Blade, CAT Genuine Parts Motorgrader Curved Double Bevel Blade, G.E.T Parts Boron Steel Center Blades with 6 holes, Through Hardened Heat Treated Cutting Edges for Motor Grader China Supplier
9W2317, 9W-2317 CAT Grader Edge 10 Holes 5/8″ Bolts Specifications:
Part No. 9W2317, 9W-2317
Weight: 98 pounds 44 kg.
Information:
BEVEL ANGLE 33.5
BOLT HOLE SIZE 18 mm
HOLE SPACING 304.8 mm
LENGTH 2436 mm
NUMBER OF HOLES 10
THICKNESS 12.7 mm
WIDTH 203.2 mm
Cutting Edges
• Complete line of curved double bevel (CDB) cutting edges for every make and model
• CDB sizes range from 1/2″ x 6″ for light grading up to heavy-duty 1″ x 8″ CDB section for greater wear life
• Flame-hardened grader cutting edges with surface hardness up to 62 RC, provides max mum wear resistance
• XHD flat grader blades are available in sizes 3/4″ x 8″ through 3″ x 16″ FDB
• Select serrated grader blades are available for frozen or hard packed ground conditions
End Bits
• HCEParts end bits and overlay end bits help protect the moldboard, while extending the life of cutting edges. End bits are available in standard and heavy-duty.
• Drop forged, triple alloy steel shanks fit precisely providing maximum strength and resistance to shock
Scarifier Shanks and Tips
• Tips are made with a tough alloy, offering maximum wear and economic value
• Tips available in rectangle and oval slot designs
Start By:a. remove oil and water pump driveb. remove accessory drive (front)c. remove auxiliary water pumpd. remove fan drivee. remove trunnionf. remove crankshaft front seal and wear sleeve 1. Remove the bolts and cover (1) from the front drive housing. Remove the O-ring seal from the cover. 2. Remove the bolts that hold plug (2) in the front drive housing. Remove the plug with tooling (A). Remove the O-ring seal from the plug. 3. Remove the bolts that hold shaft (3) in the front drive housing. Use tooling (A) to remove the shaft gear and washer from the front drive housing.4. Remove the O-ring seal from the shaft.5. Remove the bearing from the gear if necessary. 6. Remove two bolts (5) and fuel control lever (4) from the fuel control linkage 9W2315. 7. Fasten a hoist and tool (B) to the front drive housing. Remove two bolts, and install two 5/8″-11 NC guide bolts. Remove the remainder of the bolts and the front drive housing (6) from the engine. The weight of the front drive housing is 209 kg (460 lb.).Install Front Drive Housing 9W2311, 9W-2311 Tractor Curved Cutting Edge
1. Install two 5/8″-11 NC guide bolts in the end of the cylinder block. Fasten a hoist to front drive housing (1) with tooling (A). Put the gasket and front drive housing (1) in position on the guide bolts. Install the bolts to hold the front drive housing in position. Remove the guide bolts, and install the remainder of the bolts. Tighten all of the bolts evenly to their standard torques. Cut the gasket even with the bottom of the cylinder block. 2. Install fuel control lever (2) on the fuel control linkage. 3. Use tool group (B) to install the bearing in gear (3) if necessary. The bore in the bearing must be 90.00 0.06 mm (3.543 .002 in.) after assembly.4. Install O-ring seal (6) on shaft (5). Put clean engine oil on the O-ring seal.5. Put washer (4) and gear (3) in position in the front drive housing, and install shaft (5). Install the bolts that hold the shaft in place. 6. Put O-ring seal (7) in position on plug
Customized 9W2312 9W-2312 Grader Curved Blades. Put clean oil on the O-ring seal.7. Put plug (8) in position in the front drive housing, and install the bolts that hold it. 8. Put O-ring seal (10) in position on cover (9). Put clean engine oil on the O-ring seal.9. Install cover (9) on the front drive housing.End By:a. install crankshaft front seal and wear sleeveb. install trunnionc. install fan drived. install auxiliary water pumpe. install accessory drive (front)f. install oil and water pump drive 9W2315 9W2313 9W-2313 Grader Curved 8 Hole 5/8″ Cutting Edge