9W2300, 9W-2300 9 # 3/4″Holes Grader Cutting Edge

9W2300, 9W-2300 9 # 3/4″Holes Grader Cutting Edge, Low Price Dbc Grader Blades, CATERPILLAR Curved Grader Blade, CAT Genuine Parts Motorgrader Curved Double Bevel Blade, G.E.T Parts Boron Steel Center Blades with 6 holes, Through Hardened Heat Treated Cutting Edges for Motor Grader China Supplier

9W2300, 9W-2300 9 # 3/4″Holes Grader Cutting Edge Specifications:
Part No.  9W2300, 9W-2300
Weight: 61 pounds 27 kg.
Information:
BEVEL ANGLE 22.5
BOLT HOLE SIZE 21 mm
HOLE SPACING 304.8 mm
LENGTH 2131.2 mm
NUMBER OF HOLES 9
THICKNESS 12.7 mm
WIDTH 152.4 mm

Cutting Edges
• Complete line of curved double bevel (CDB) cutting edges for every make and model
• CDB sizes range from 1/2″ x 6″ for light grading up to heavy-duty 1″ x 8″ CDB section for greater wear life
• Flame-hardened grader cutting edges with surface hardness up to 62 RC, provides max mum wear resistance
• XHD flat grader blades are available in sizes 3/4″ x 8″ through 3″ x 16″ FDB
• Select serrated grader blades are available for frozen or hard packed ground conditions

End Bits
• HCEParts end bits and overlay end bits help protect the moldboard, while extending the life of cutting edges. End bits are available in standard and heavy-duty.
• Drop forged, triple alloy steel shanks fit precisely providing maximum strength and resistance to shock

Scarifier Shanks and Tips
• Tips are made with a tough alloy, offering maximum wear and economic value
• Tips available in rectangle and oval slot designs

Start By:a. remove radiator 1. Remove the nuts and bolts (2) that hold the trunnion to the engine front support. Put two 50 ton screw jacks in position under the front drive housing at location (X).  9W2295 9W-2295 CARBON LEVEL BLADE 7 # 5/8″ Hole  Raise the engine with the jacks until the trunnion is approximately 51 mm (2 in.) above the engine front support.2. Fasten tooling (A) to tube assembly (4) at locations (Y).3. Fasten tooling (A) to engine front support (3) with two nylon straps. 9W2294, 9W-2294 China Grader Blade Ground Engaging Tools

4. Remove four bolts (1) that hold the engine front support to the frame.5. Use tooling (A) to lower engine front support (3) to the ground. The weight of the engine front support is 83 kg (183 lb.). The following steps are for installation of the engine front support.6. Make sure the mating surfaces of the engine front support, trunnion and the frame are free of paint.7. Fasten tooling (A) to engine front support (3). Use tooling (A) to put the engine front support in position in the frame.8. Install four bolts (1) that hold the engine front support to the frame. Tighten the bolts to a torque of 475 50 N m (350 37 lb.ft.).9. Remove tooling (A) from the engine front support and tube assembly (4).10. Use the two 50 ton screw jacks to lower the engine into position on the engine front support.11. Install bolts (2). Tighten the bolts to a torque of 475 50 N m (350 37 lb.ft.).End By:a. install radiator 9W2293 9W-2293 Garden tractor grader blade front dozer blade

Typical Example3. Put O-ring seals (8) in position on each end of core assembly (1).4. Align the connector in the bottom of the core assembly with adapter (9). Install core assembly (1). Install the bolts that hold the core assembly in place. 5. Fasten a hoist and tooling (A) to housing (10). Put the gasket and housing (10) in position, and install the spacers and bolts to hold it in place. Tighten the bolts to a torque of 55 7 N m (41 5 lb.ft.). 6. Make sure O-ring seal (12) is in position on adapter (11).7. Put glycerine on the bores of the adapter and the housing. Install adapter (11) and the sleeve in the front of the aftercooler. 8. Make sure O-ring seal (14) is in position on adapter (13).9. Put glycerine on the bores of the adapter and the housing. Install adapter (13) and the sleeve in the rear of the aftercooler. 10. Install elbow (15) on the front of the aftercooler. 11. Install shields (16) and (17) over the exhaust manifolds.12. Make sure the gasket is in position on the cylinder block. Put adapter (18) in position in the end of the aftercooler and on the cylinder block. Install the bolts that hold it.13. Connect two wires (19) to the switch. 14. Install the gasket on adapter (18).15. Put elbow (21) in position in hose (20) and on adapter (18). Install the bolts that hold elbow (21) to the 9W2296 Double Bevel Curved Motor Grader Blade 7 # 3/4″ Hole