9W2293 CAT 5/8″ Holes 4FT Curved Carbon Grader Blade, Low Price Dbc Grader Blades, CATERPILLAR Curved Grader Blade, CAT Genuine Parts Motorgrader Curved Double Bevel Blade, G.E.T Parts Boron Steel Center Blades with 6 holes, Through Hardened Heat Treated Cutting Edges for Motor Grader China Supplier
9W2293 CAT 5/8″ Holes 4FT Curved Carbon Grader Blade Specifications:
Part No. 9W2293 , 9W-2293
Weight: 33 pounds 14 kg.
Information:
BEVEL ANGLE 22.5
BOLT HOLE SIZE 18 mm
HOLE SPACING 304.8 mm
LENGTH 1216.8 mm
NUMBER OF HOLES 6
THICKNESS 12.7 mm
WIDTH 152.4 mm
Cat motor grader cutting edges provide the best balance of abrasion and impact resistance. Both Cat cutting edges and end bits are designed as a balanced system to move more material over a longer period with less downtime. This is accomplished by providing great strength for superior breakage resistance, and by offering maximum wear protection from both bottom and face wear on the cutting edge.
Cutting Edges
• Complete line of curved double bevel (CDB) cutting edges for every make and model
• CDB sizes range from 1/2″ x 6″ for light grading up to heavy-duty 1″ x 8″ CDB section for greater wear life
• Flame-hardened grader cutting edges with surface hardness up to 62 RC, provides max mum wear resistance
• XHD flat grader blades are available in sizes 3/4″ x 8″ through 3″ x 16″ FDB
• Select serrated grader blades are available for frozen or hard packed ground conditions
End Bits
• HCEParts end bits and overlay end bits help protect the moldboard, while extending the life of cutting edges. End bits are available in standard and heavy-duty.
• Drop forged, triple alloy steel shanks fit precisely providing maximum strength and resistance to shock
Scarifier Shanks and Tips
• Tips are made with a tough alloy, offering maximum wear and economic value
• Tips available in rectangle and oval slot designs
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, “General Hazard Information and High Pressure Fuel Lines” for safety information.Refer to Systems Operation, Testing and Adjusting Manual, “Cleanliness of Fuel System Components” for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates. 9J3659 China Double Bevel Flat Motor Grader Cutting Edge
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Raise the hood. 9J3659, 9J-3659 China Low Price Dbc Grader Blades
Turn the battery disconnect switch to the OFF position.
Cleanliness is an important factor. Thoroughly clean the exterior of the component before commencing the disassembly procedure. Thoroughly cleaning the exterior of the component will help to prevent dirt from entering the internal mechanism.
Illustration 1 g02626186 8J9821, 8J-9821 Motor Tractor Grader 14H 160H 160M Curved Blade
Remove bolt (2) from the soot antenna wire clamps. Remove bolts (3) and remove shield (1) .
Illustration 2 g02626170
Remove cable straps (6) and (9) .
Disconnect harness assemblies (4) and (5) . 8J9821 Caterpillar 14H 160H 160M Curved Edges for Grader
Disconnect hose assemblies (8) and (10). Use Tooling (A) in order to plug the hose assembly with a new plug. Use Tooling (A) in order to cap the connection with a new plug.
Remove bolts (11) and remove fuel control manifold (7) .
Illustration 3 g02626209 7T1643, 7T1645 Caterpillar Curved Edges for Machinery Graders
Remove fuel pressure sensor (16) from fuel control manifold (7). Remove O-ring seal (18) .
Remove nut (12) from the valve assembly and remove solenoid (13). Remove valve assembly (14) from fuel control manifold (7) .