9W2293 9W-2293 Garden tractor grader blade front dozer blade

9W2293 9W-2293 Garden tractor grader blade front dozer blade 13 5/8″ Holes, Low Price Dbc Grader Blades, CATERPILLAR Curved Grader Blade, CAT Genuine Parts Motorgrader Curved Double Bevel Blade, G.E.T Parts Boron Steel Center Blades with 6 holes, Through Hardened Heat Treated Cutting Edges for Motor Grader China Supplier

9W2293 9W-2293 Garden tractor grader blade front dozer blade 13 5/8″ Holes Specifications:
Part No. 9W2293 , 9W-2293, 3G8016 , 3G-8016
Weight: 33 pounds 14 kg.
Information:
BEVEL ANGLE 22.5
BOLT HOLE SIZE 18 mm
HOLE SPACING 304.8 mm
LENGTH 1216.8 mm
NUMBER OF HOLES 6
THICKNESS 12.7 mm
WIDTH 152.4 mm

Cat motor grader cutting edges provide the best balance of abrasion and impact resistance. Both Cat cutting edges and end bits are designed as a balanced system to move more material over a longer period with less downtime. This is accomplished by providing great strength for superior breakage resistance, and by offering maximum wear protection from both bottom and face wear on the cutting edge.

Cutting Edges
• Complete line of curved double bevel (CDB) cutting edges for every make and model
• CDB sizes range from 1/2″ x 6″ for light grading up to heavy-duty 1″ x 8″ CDB section for greater wear life
• Flame-hardened grader cutting edges with surface hardness up to 62 RC, provides max mum wear resistance
• XHD flat grader blades are available in sizes 3/4″ x 8″ through 3″ x 16″ FDB
• Select serrated grader blades are available for frozen or hard packed ground conditions

End Bits
• HCEParts end bits and overlay end bits help protect the moldboard, while extending the life of cutting edges. End bits are available in standard and heavy-duty.
• Drop forged, triple alloy steel shanks fit precisely providing maximum strength and resistance to shock

Scarifier Shanks and Tips
• Tips are made with a tough alloy, offering maximum wear and economic value
• Tips available in rectangle and oval slot designs

3. Disconnect hose assemblies (2) and (3) from the bonnet.4. Remove the four bolts, and disconnect elbow (4) from the lower brake oil cooler.5. Loosen the hose clamp that holds the hose to elbow (1). Move the hose away from the elbow. 6. Remove the four bolts and block (5) from the lower brake oil cooler. 7. Disconnect the hose assemblies from upper brake oil cooler (8).8. Remove the bolt and clamps (10) from tube (7).9. Remove the bolts and retainers from each end of tube (7), and remove the tube.10. Fasten a hoist to the brake oil coolers.11. Remove the bolts that hold bonnets (6) and (9) to the brackets. Remove brake oil coolers (8) and (11) and the bonnets as an assembly. The weight of the assembly is 130 kg (287 lb.). 9J3659, 9J-3659 China Low Price Dbc Grader Blades

12. If necessary, put alignment marks on the brake oil coolers and bonnets (6) and (9), and remove the bonnets from the oil coolers. The following steps are for installation of the brake oil coolers. Also, make sure the tubes in the oil coolers are clean and free of dirt and other foreign material.13. Put clean engine oil on all of the O-ring seals.14. Make sure the gaskets and O-ring seals are in position, and install bonnets (6) and (9) on the brake oil coolers.15. Fasten a hoist to the brake oil coolers. Put the oil coolers and bonnets in position on the brackets, and install the bolts that hold them in place.16. Put tube (7) in position, and install the retainers and bolts at each end of the tube. Install clamps (10) and the bolt to hold tube (7) in place.17. Connect the hose assemblies to upper brake oil cooler (8).18. Put block (5) in position on the rear of the lower brake oil cooler, and install the four bolts that hold it.19. Put the hose back into position on elbow (1), and tighten the hose clamps that hold it in place.20. Put elbow (4) in position on the front of the lower brake oil cooler, and install the four bolts that hold it.21. Connect hose assemblies (2) and (3).22. Fill the cooling system with coolant to the correct level. See the Maintenance Manual.23. Fill the hydraulic tank with oil to the correct level. See the Maintenance Manual.9J7701, 9J-7701 China Motor Grader Blades