9J3659 China Double Bevel Flat Motor Grader Cutting Edge

9J3659 China Double Bevel Flat Motor Grader Cutting Edge, CATERPILLAR Curved Grader Blade, CAT Genuine Parts Motorgrader Curved Double Bevel Blade, G.E.T Parts Boron Steel Center Blades with 17 holes, Through Hardened Heat Treated Cutting Edges for Motor Grader China Supplier

9J3659 China Double Bevel Flat Motor Grader Cutting Edge Specifications:
Part No. 9J3659 , 9J-3659
Weight: 60 pounds 27 kg.
Information:
BEVEL ANGLE 22.5
BOLT HOLE SIZE 21 mm
HOLE SPACING 152.4 mm
LENGTH 2131.2 mm
NUMBER OF HOLES 15
THICKNESS 12.7 mm
WIDTH 152.4 mm

Compatible equipment models: 9J3659 :
MOTOR GRADER 14G 14H 14H NA 14M 160H 160H NA 160M 160M 2 163H 163H NA 16G Caterpillar

Cat motor grader cutting edges provide the best balance of abrasion and impact resistance. Both Cat cutting edges and end bits are designed as a balanced system to move more material over a longer period with less downtime. This is accomplished by providing great strength for superior breakage resistance, and by offering maximum wear protection from both bottom and face wear on the cutting edge.

Material: Manganese steel, boron steel
Thickness: 13mm; 16mm; 19mm; 25mm.
Width: 152mm and 203mm.
Length: 4=1219mm; 5=1524mm; 6=1828mm; 7=2133mm; 8=2438mm.
Bolts Dia: 3/4; 5/8
Adaptable for most of graders in market, including Komatsu, Caterpillar, Hitachi, Sumitomo, Kato, Daewoo, etc, also could be designed and produced by clients’ drawing.
Mechanical properties of products could reach international standard after quenching and tempering heat treatment.
Thanks to our high quality raw material and professional heat treatment, our products’ wear life and performance of are 15% ~ 20% higher than most of other similar products in market.
Trade Terms: FOB NINGBO.
Payment Terms: 30% prepaid, T/T at the sight of copy of B/L.

Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, “General Hazard Information and High Pressure Fuel Lines” for safety information.Refer to Systems Operation, Testing and Adjusting Manual, “Cleanliness of Fuel System Components” for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Raise the hood.
Turn the battery disconnect switch to the OFF position.
Cleanliness is an important factor. Thoroughly clean the exterior of the component before commencing the disassembly procedure. Thoroughly cleaning the exterior of the component will help to prevent dirt from entering the internal mechanism.
Illustration 1 g02626186
Remove bolt (2) from the soot antenna wire clamps. Remove bolts (3) and remove shield (1) .
Illustration 2 g02626170
Remove cable straps (6) and (9) .
Disconnect harness assemblies (4) and (5) .
Disconnect hose assemblies (8) and (10). Use Tooling (A) in order to plug the hose assembly with a new plug. Use Tooling (A) in order to cap the connection with a new plug.
Remove bolts (11) and remove fuel control manifold (7) .
Illustration 3 g02626209  7T1643, 7T1645 Caterpillar Curved Edges for Machinery Graders
Remove fuel pressure sensor (16) from fuel control manifold (7). Remove O-ring seal (18) .
Remove nut (12) from the valve assembly and remove solenoid (13). Remove valve assembly (14) from fuel control manifold (7) .