Working time parameters of excavator and parts maintenance plans

Two checks are required before starting:

1. Check the oil level, open the fuel switch, and confirm (lubricating oil, fuel) with or without leakage.
2. Check the air filter and block indicator, check the coolant level and radiator, turn on the main power switch, set the throttle to idle, disengage the clutch or place the transmission in neutral.

Checks that need to be done before stopping:

First let the engine run at light load for 3 minutes, disengage the clutch or place the rotating device in neutral, press the stop button, disconnect the electrical system after the engine stops, check the equipment for leaks, and if it is to be shut down for a while, it should be disconnected. Main power switch.

Excavator maintenance plan (including 50 hours, 250 hours, 400 hours, 50-250 hours, 800 hours, 1000 hours, 2000 hours)

For every 250 hours of operation, the engine oil should be replaced. The oil should be added to meet the oil standard requirements of the equipment manufacturer.

Every 50 hours of operation, check the fuel oil water separator to discharge the separated water and impurities.

Working time parameters of excavator and parts maintenance plans

Working time parameters of excavator and parts maintenance plans

Change lubricant, lube filter and bypass filter for every 50-250 hours/maximum every 12 months.

Drain the fuel in the fuel tank every 400 hours/maximum every 12 months. Clean the fuel tank. Check or replace the fuel filter.

Check the intake line for leaks and leaks on the joint surface of the functional unit every 800 hours/maximum every 12 months.

Replace the coolant filter every 1000 hours / every 6 months, do not replace the coolant at the same time.

Every 2000 hours, check the turbocharger, check and adjust the valve clearance, replace the coolant, check the electrical system every 12 months using a diagnostic tool, general inspection, replace the air filter, clean the engine, replace the fuel tank vent filter , replace the air compressor filter.

Check/flush the cooling system and replace the coolant every 10,000 hours/maximum every 48 months.

For the use of lubricating oil, coolant and fuel, please strictly follow the requirements of the equipment manufacturer and regularly replace the lubricating oil and coolant that meet the standard.

The fuel should be the standard oil of the regular channel, and the sulfur content should not exceed 1.5%.

Long-term unused storage preparation work

The storage period is less than 8 months, the engine oil and lubricating oil filter are replaced, and then run to the normal working temperature for more than 8 months. The lubricating oil and fuel system are maintained with protective oil.

BRAND MODEL PART NO. DESCRIPTION WEIGHT(KG) SPECIFICATION
CATERPILLAR 966 D/E Rock 4T9123 Right Hand Segment 25 1-3/16 x14-11/64 x 10-7/16
CATERPILLAR 966 D/E Rock 4T9124 Left Hand Segment 25 1-3/16 x14-11/64 x 10-7/16
CATERPILLAR 966 D/E Rock 1359648 Caribided NonRev Seg
CATERPILLAR 966 D/E Rock 1359649 Caribided NonRev Seg
CATERPILLAR 966 D/E Rock 1359647 Caribided NonRev Seg blades on bulldozer
CATERPILLAR 966 D/E/F General Purpose 7V1490 Base Edge NO Seg Holes 255 1-1/2x 12 x 119-3/8
CATERPILLAR 966 D/E/F General Purpose 4V7175 RH Corner 1 Hole 9 1-3/8 x 10 x 9
CATERPILLAR 966 D/E/F General Purpose 4V7174 LH Corner 1 Hole 9 1-3/8 x 10 x 9
CATERPILLAR 966 D/E/F General Purpose 8E5310 RH Corner 2 Hole 15 2 x 8-3/4 x 10-3/4
CATERPILLAR 966 D/E/F General Purpose 8E5311 LH Corner 2 Hole 15 2 x 8-3/4 x 10-3/4
CATERPILLAR 966 D/E/F General Purpose 1U0593 Center Blade 95 1-3/16 x14-11/64 x 51-7/8
CATERPILLAR 966 D/E/F General Purpose 3G6395 End Blades 25 1 x 6-1/4 x 13-9/16 blades on bulldozer
CATERPILLAR 966 D/E/F General Purpose 1U1897 Angled End Bit 30 1-3/8 x 7-7/8 x 23-5/8
CATERPILLAR 966 D/E/F General Purpose 1004046 Heavy Duty Center 135 1-3/8 x 7-7/8x 23-5/8
CATERPILLAR 966 D/E/F General Purpose 1004044 Heavy Duty End 31 1-3/8 x 16x 51-7/8
CATERPILLAR 966 D/E/F General Purpose 9W3477 Carbided NonRev CTR 76 1-1/8 x 11 x51-7/8
CATERPILLAR 966 D/E/F General Purpose 9W3478 Carbided NonRev CTR 76 1-1/8 x 11 x51-7/8
CATERPILLAR 966 D/E/F General Purpose 1230336 Carbided NonRev END 23 1-3/8 x 8 x 18-1/4
CATERPILLAR 966 D/E/F General Purpose 1230337 Carbided NonRev END 23 1-3/8 x 8 x 18-1/4
CATERPILLAR 966 D/E/F General Purpose 9W6749 Rear Wear Plate 37 1-3/8 x 10x 22-1/4 blades on bulldozer
CATERPILLAR 966 D/E/F General Purpose 9V6575 Base Edge W/Seg Holes 255 1-1/2x 12 x 119-3/4
CATERPILLAR 966 D/E/F General Purpose 4V7175 RH Corner 1 Hole 9 1-3/8 x 10 x 9
CATERPILLAR 966 D/E/F General Purpose 4V7174 LH Corner 1 Hole 9 1-3/8 x 10 x 9

8V7453 953 943 TRACK LOADER Bolt-on Base Edge 25mm

9R-8985 9R8985 Caterpillar BACKHOE LOADER Base Blade

9V6570, 9V-6570 943, 953 TRACK LOADER Base Edge

9V3561 9V-3561 Caterpillar Loader Blade Cutting Edge

8V9580, 8V-9580 WHEEL LOADER Welded Cutting Edge 45mm

8V7453 8V-7453 Cat Loader 943 Multi-Purpose Bolt-on Edge

8Y4738, 8Y-4738 TRACK LOADER Base Blade 20mm

8V9585, 8V-9585 988B WHEEL LOADER Base Blade

China Loader Spade Base Edge 9V3561 9V-3561

Caterpillar 966C Wheel Loader Base Blade 9V-0169 9V0169

9C2932, 9C-2932 Cat style Weld-on Base Edge 51mm

9V6574 9V-6574 973C, 980C, 980F Loader Base Edge

8Y5291, 8Y-5291 TRACK LOADER Weld-on Base Edge 16mm